HPE and Aruba connection templates
HP and Aruba switches span two CLI families with different paging commands and login quirks. The hp/ folder holds eight templates and aruba/ holds two, all Core and Pro. This page covers release v2.2.2.
Which template
| Template | Use for |
|---|---|
hp-procurve-ssh-noenable |
ProCurve over SSH. Start here |
hp-procurve-ssh-noenable-nopage |
ProCurve firmware without the swallowed-character quirk |
hp-procurve-telnet-noenable |
ProCurve over telnet |
hp-comware-ssh-noenable |
Comware, including H3C-branded hardware |
hp-comware-ssh-noenable-flexfabric |
FlexFabric switches |
hp-comware-ssh-noenable-nosystemview |
The A5120, without entering system-view |
hp-comware-5400xl-ssh-noenable |
The 5400xl |
hp-1920-ssh-enable |
The 1920, which needs its own elevation command |
aruba-aos-s-ssh-noenable |
AOS-S (written against a 2930F) |
aruba-aos-ssh-enable |
ArubaOS with enable (written against an S3500) |
ProCurve and AOS-S switches turn paging off with no page. Comware uses screen-length disable. ArubaOS uses no paging.
Press any key, and the doubled letter
ProCurve and AOS-S switches show a “Press any key to continue” screen after login and dress their output in VT100 terminal codes. Templates for them set hpAnyKeyStatus: on, which sends the keystrokes to get past that screen and cleans the terminal codes from the captured output.
The standard ProCurve template’s paging command is nno page. The doubled letter is deliberate: some HPE firmware swallows the first character sent after the any-key screen, so the extra n is sacrificial and the switch receives no page. Don’t correct it. If the session log shows an error such as Invalid input: nno, your firmware doesn’t have the quirk: use the nopage template, which sends no page as written.
The 1920
The 1920 keeps its model number in the filename because it needs an elevation command other HP switches don’t. The template uses the enable step to send _cmdline-mode on and then the y that confirms it, both inside enableCmd.
The templates
rConfig-templates / hp /hp-procurve-ssh-noenable.ymlView on GitHub- Protocol
- SSH, port 22
- Any key
- hpAnyKeyStatus: on
- Paging
- nno page
- Status
- community-tested
- Protocol
- SSH, port 22
- Any key
- hpAnyKeyStatus: on
- Paging
- no page
- Status
- community-tested
- Protocol
- Telnet, port 23
- Any key
- hpAnyKeyStatus: on
- Paging
- no page
- Status
- community-tested
- Protocol
- SSH, port 22
- Enable
- off
- Paging
- screen-length disable
- Status
- community-tested
- Protocol
- SSH, port 22
- Any key
- hpAnyKeyStatus: on
- Paging
- screen-length disable
- Status
- community-tested
- Protocol
- SSH, port 22
- Enable
- off
- Paging
- screen-length disable
- Status
- community-tested
- Protocol
- SSH, port 22
- Any key
- hpAnyKeyStatus: on
- Paging
- screen-length disable
- Status
- community-tested
- Protocol
- SSH, port 22
- Enable
- _cmdline-mode on, then y
- Paging
- screen-length disable
- Status
- community-tested
- Protocol
- SSH, port 22
- Any key
- hpAnyKeyStatus: on
- Paging
- no page
- Status
- community-tested
- Protocol
- SSH, port 22
- Enable
- on
- Paging
- no paging
- Status
- community-tested
What to put in the command group
The ProCurve telnet template carries a note that the retrieval command should be show config rather than show startup-config. The other templates don’t name one.